南水北调中线工程安阳段渠坡换填土的强度特性研究

为了分析南水北调中线工程安阳段渠坡的稳定性,对该渠坡换填土在不同含水率下进行了不固结不排水三轴剪切试验.研究结果表明:剪切速率对基质吸力的影响较大,而对强度的影响较小;通过比较确定了合适的剪切速率;含水率相同的试样在不同围压下的强度值在pf -qf坐标上呈良好的线性关系;得到了试样在不同含水率下的总强度指标,建立了总内...     

基于遗传算法的跳频通信侦察技术

为了识别跳频序列,提出了采用遗传算法并结合跳频信号特点来完成跳频序列的分析与重组,从而实现跳频信号的侦察。在采用传统遗传算法的基础上,针对序列特点提出了5种改进手段,从而大大提高了算法的效率和可用性。最后利用采样的语音信号,对分析与重组过程进行模拟来验证算法的可行性。     

概率分布模型的飞机战备完好率评估与预测

飞机战备完好率是军用飞机战斗力的重要体现.在分析目前部队常用的飞机战备完好率算法缺陷的基础上,建立了基于概率分布的飞机战备完好率计算模型,该模型体现了飞机任务可靠性、维修性与战备完好性之间的关系.以某型飞机为例,通过分析飞机任务可靠度,利用飞机可靠性、维修性、保障性及作战训练任务的历史统计数据,依据概率分布模型对飞机的...     

混沌序列网形跳频网络同步方案

跳频信号的同步过程是跳频通信系统的关键.针对网形跳频网络中同步难的问题,提出了一种基于混沌序列的动态双频跳频同步方案.该方案采用混沌系统生成分布式跳频序列,同时引入并行解调器结构实现双频跳变的时序控制.仿真结果表明,方案可有效应对慢跳频通信系统中常见的部分频带干扰和强单频干扰,且同步建立过程简单迅速,系统的稳定性和安全...     

Effect of organo-modified montmorillonite nanoclay on mechanical,thermal and ablation behavior of carbon fiber/phenolic resin composites

The mechanical, thermal and ablation properties of carbon phenolic (C-Ph) composites (Type-I) rein-forced with different weight percentages of organo-modified montmorillonite (o-MMT) nanoclay have been studied experimentally. Ball milling was used to disperse different weight (wt) percentages (0, 1,2,4,6 wt.％) of nanoclay into phenolic resin. Viscosity changes to resin due to nanoclay was studied. On the other hand, nanoclay added phenolic matrix composites (Type-II) were prepared to study the dispersion of nanoclay in phenolic matrix by small angle X-ray scattering and thermal stability changes to the matrix by thermogravimetric analyser (TGA). This data was used to understand the mechanical, thermal and ablation properties of Type-I composites. Inter laminar shear strength (ILSS), flexural strength and flexural modulus of Type I composites increased by about 29％, 12％and 7％respectively at 2 wt.％ addition of nanoclay beyond which these properties decreased. This was attributed to reduced fiber volume fraction (％Vf) of Type-I composites due to nanoclay addition at such high loadings. Mass ablation rate of Type-I composites was evaluated using oxy acetylene torch test at low heat flux (125 W/cm2) and high heat flux levels (500 W/cm2). Mass ablation rates have increased at both flux levels marginally up to 2 wt.％ addition of nanoclay beyond which it has increased significantly. This is in contrast to increased thermal stability observed for Type-I and Type-Ⅱ composites up to 2 wt.％addition of nanoclay. Increased ablation rates due to nanoclay addition was attributed to higher insulation effi-ciency of nanolcay, which accumulates more heat energy in limited area behind the ablation front and self-propagating ablation mechanisms triggered by thermal decomposition of organic part of nanoclay.     

A higher order coupled frequency characteristics study of smartmagneto-electro-elastic composite plates with cut-outs using finite element methods

This article deals with investigating the effect of cut-outs on the natural frequencies of magneto-electro-elastic (MEE) plates incorporating finite element methods based on higher order shear deformation theory (HSDT). In order to consider the influence of cut-out, the energy of the cut-out domain is sub-tracted from the total energy of the entire plate. The governing equations of motions are derived through incorporating Hamilton's principle and the solution is obtained using condensation technique. The proposed numerical formulation is verified with the results of previously published literature as well as the numerical software. In addition, this research focuses on evaluating the effect of geometrical skewness and boundary conditions on the frequency response. The influence of cut-outs on the degree of coupling between magnetic, electric and elasticfields is also investigated.     

A novel formulation of material nonlinear analysis in structural mechanics

This article demonstrates a novel approach for material nonlinear analysis. This analysis procedure eliminates tedious and lengthy step by step incremental and then iterative procedure adopted classically and gives direct results in the linear as well as in nonlinear range of the material behavior. Use of elastic moduli is eliminated. Instead, stress and strain functions are used as the material input in the analysis procedure. These stress and strain functions are directly derived from the stress-strain behavior of the material by the method of curve fitting. This way, the whole stress-strain diagram is utilized in the analysis which naturally exposes the response of structure when loading is in nonlinear range of the material behavior. It is found that it is an excellent computational procedure adopted so far for material nonlinear analysis which gives very accurate results, easy to adopt and simple in calculations. The method eliminates all types of linearity assumptions in basic derivations of equations and hence, eliminates all types of possibility of errors in the analysis procedure as well. As it is required to know stress distribution in the structural body by proper modelling and structural idealization, the proposed analysis approach can be regarded as stress-based analysis procedure. Basic problems such as uniaxial problem, beam bending, and torsion problems are solved. It is found that approach is very suitable for solving the problems of fracture mechanics. Energy release rate for plate with center crack and double cantilever beam specimen is also evaluated. The approach solves the fracture problem with relative ease in strength of material style calculations. For all problems, results are compared with the classical displacement-based liner theory.     

玻璃瓶动态图像检测运动模拟平台

动态图像检测中,如何在指定位置快速而准确地捕捉到运动物体的图像是最基本的环节。试验验证图像检测装置的成像特性,成为动态图像检测研究的重要内容之一。以变频器控制电动机为核心,通过变频器内部参数编程和外部简单的辅助控制电路,构建了运动平稳、速度可调、具有自动保护功能的模拟平台。该平台适于动态图像检测中普通运动物体的快速模拟,已成功地用于玻璃瓶动态图像装置中,达到了预期目的。     

N、P源对微生物法处理石油烃效果的影响

在微生物法处理石油烃的过程中,微生物对N、P源的供给非常敏感,不同的微生物对不同的N、P源的生物利用度是不相同的,N、P源的选择对降解效果有较大影响,所以有必要对最佳的N、P源进行筛选。对N、P源的逸择和加入量对降解效果的影响进行了研究,确定了最佳的N、P源分别为(NH4)2SO4、KH2PO4。在(NH4)2SO4、KH2PO4的质量浓度分别为100mg／L和60mg／L时,废水中石油烃的去除率最高。     

非局部弹性杆固有频率的Ritz法求解

采用Ritz法求解了非局部弹性直杆的固有频率问题。非局部弹性理论与经典弹性理论相对应,区别在于非局部理论中,一点的应力与该点以及其周围区域的应变都有关,并采用核函数来表征这种相关性。基于Eringen提出的非局部弹性模型,针对三种给定核函数,用Ritz法进行了直杆的动力学分析。并针对两种边界条件给出直杆的固有频率,与其它方法比较,该方法具有可以针对多种核函数求解,精度可控,易于编程等优点。